The thinnest, smoothest metallic lines in the world helps speed up miniaturisation of electronic devices

Singapore, 6 July - New method creates super-thin, high integrity, continuous metal lines that surpass today’s semiconductor industry requirements.

*For immediate release*

Scientists from Singapore A*STAR’s Institute of Materials Research and Engineering (IMRE), University of Cambridge (UK) and Sungkyunkwan University (South Korea) have created metallic lines so thin and smooth that they can only be seen using powerful electron microscopes. This research will be published in the July issue of Advanced Functional Materials, the leading full-paper materials science journal.

At line widths of just 7 nm, their line width roughness , which are the variations in thickness along the line itself, stands at 2.9 nm, a value which is below the 2010 target of 3.2 nm and closer to 2011’s target line width roughness of 2.8 nm indicated in the International Technology Roadmap for Semiconductors .

The ability to create such distinct lines and patterns on a sub-10 nm scale level is essential in the further miniaturisation of electronic components. Rough, undefined patterns and lines results in poorly made, energy-inefficient devices. The process is very delicate and precise because of the scale at which the work is done. For comparison, the width of the average human hair is 100 µm, which is about 14,000 times the width of a single 7 nm-wide metal line.

“Our thin, unbroken and smooth lines are important in ensuring the efficiency of ever shrinking electronic devices and may lead to more powerful processors. Furthermore, our work shows that continuous metallic lines as small as 4 nm are possible to make”, says Dr MSM Saifullah, a Research Scientist with IMRE. The method could be potentially used to make interconnects, the ‘highways’ that carry electrical pulses and data in extremely small integrated circuits (ICs). The smoother and uninterrupted ‘highways’ lead to faster data transfer rates and less energy wasted, in the form of heat.

The novelty of the method was in the material and the technique that was used. The current “lift-off” approach for making metal lines at this scale requires more steps, uses more materials and results in rough, and quite often broken lines on a sub-10 nm scale. The researchers used an organometallic material which is made up of a metallic and an organic component. Using a combination of electron beam lithography and subsequent gas treatment, the researchers were able to easily chip away the organic portions in a uniform manner, leaving the desired metallic patterns, in this case, thin metal lines.

“The published results is a testament to the cutting-edge nanotechnology research that is done in Singapore, where we push, and sometimes lead, the rest of the world”, says Prof Andy Hor, IMRE’s new Executive Director, who took the helm of Singapore’s materials research institute in June 2010.

“Our obvious expertise in the area of nanopatterning is also a reason why we are driving a concerted effort for the industry to adopt technologies such as this into their manufacturing processes”, explains Prof Hor. IMRE will be launching an Industrial Consortium on Nanoimprinting (ICON) on 3 August 2010 to encourage industry to take full advantage of the benefits that advanced nanopatterning has to offer.

The research on the metal lines will be featured on the inside front cover of Issue 14 (July 2010) of the Advanced Functional Materials journal.

Encl. Annex A: Corporate Profiles
Annex B: Results
– END –
________________________________________
For media enquiries, please contact:
Mr Eugene Low
Manager, Corporate Communications
for Institute of Materials Research and Engineering (IMRE)
3, Research Link
Singapore 117602
DID +65 6874 8491
Mobile +65 9230 9235
Email [email protected]

For technical and business enquiries, please contact:
Dr MSM Saifullah
Research Scientist
Institute of Materials Research and Engineering (IMRE)
3, Research Link
Singapore 117602
DID +65 6874 1484
Email [email protected]

Mr Rick Ong
Industry Development Manager
Institute of Materials Research and Engineering (IMRE)
3, Research Link
Singapore 117602
DID +65 6513 1198
Email [email protected]

Annex A – Corporate Profiles

About the Institute of Materials Research and Engineering (IMRE)
Established in September 1997, IMRE has built strong capabilities in materials analysis, characterisation, materials growth, patterning, fabrication, synthesis and integration. IMRE is an institute of talented researchers equipped with state-of-the-art facilities such as the SERC Nanofabrication and Characterisation Facility to conduct world-class materials science research. Leveraging on these capabilities, R&D programmes have been established in collaboration with industry partners. These include research on organic solar cells, nanocomposites, flexible organic light-emitting diodes (OLEDs), solid-state lighting, nanoimprinting, microfluidics and next generation atomic scale interconnect technology.

For more information about IMRE, please visit www.imre.a-star.edu.sg

About the Agency for Science, Technology and Research (A*STAR)
The Agency for Science, Technology and Research (A*STAR) is the lead agency for fostering world-class scientific research and talent for a vibrant knowledge-based and innovation-driven Singapore. A*STAR oversees 14 biomedical sciences, and physical sciences and engineering research institutes, and seven consortia & centres, which are located in Biopolis and Fusionopolis, as well as their immediate vicinity.

A*STAR supports Singapore's key economic clusters by providing intellectual, human and industrial capital to its partners in industry. It also supports extramural research in the universities, hospitals, research centres, and with other local and international partners.

For more information about A*STAR, please visit www.a-star.edu.sg.

Annex B – Results

Material Copper naphthenate Copper
Line width, nm (average) 10 nm ~5 nm
Pattern height, nm ~75 nm ~50 nm
Aspect ratio ~7.5 ~10
LWR (3LWRσ), nm 1.9 -

Table I: Line width, aspect ratio, and LWR obtained for the line patterns of copper naphthenate and copper.

Nanoscale lines of (a) copper naphthenate and (b) copper after hydrogen reduction showing size reduction by about 50%, to make the metal lines - the thinnest ever made to date.

a

Nanoscale lines of (a) copper naphthenate and (b) copper after hydrogen reduction showing size reduction by about 50%, to make the metal lines - the thinnest ever made to date.

b

Published: 13 Oct 2010

Contact details:

General inquiries

1 Fusionopolis Way, #20-10
Connexis North Tower
Singapore 138632

(65) 6826 6111
Country: 
News topics: 
Content type: